Notice: Undefined index: viewed_product_ids in /var/www/vhosts/ on line 19 Magura Olives (2)
  • Opening Hours.
    Fri: 9.00am to 5.00pm (UK)
  • United Kingdom.
    01772 32 33 33
  • International.
    0044 1772 32 33 33

Magura Olives (2)

Product code: 28


In stock

Magura Olives (2)

- Official Magura olive for Magura HS11, HS33 and low pressure disc brake nylon hoses.
- Essential spare for all hydraulic rim brake users, allowing a broken hose to be repaired within minutes, and get you back out riding again!
- Compatible with black, blue and red Magura hose, plus Racing Line and Trialtech.
- Sold as a pack of two (enough for one complete hose: one olive at each end).
- Alternatives are available in case these are out of stock: Trialtech Olives.


Phil J

Hi, do you know if these olives compatible with the old low pressure Magura Julie brakes? Thanks, Phil

Posted by Phil J on 08/07/2013

Reply from TartyBikes on 08/07/2013

Hi Phil - thanks for your question. As far as we know they should work with that brake with a plastic hose. Thanks, Flipp.

rene kempfner

Can I use these olives on my old school flouro-yellow Magura HS33 (Olympia Tomac) ?

Posted by rene kempfner on 17/07/2013

Reply from TartyBikes on 18/07/2013

Hi Rene - yes, you can use these olives on that brake. Thanks, Flipp.


Hi do these olives fit HS11 brakes from about 2001, please?

Posted by Andrew on 04/01/2014

Reply from TartyBikes on 06/01/2014

Hi Andrew - thanks for your question. The olives used in Magura brakes have always been the same so these should work with your brakes absolutely fine. If you still have the factory originals installed, these may look a little different (these are black and will work either way around, where the originals will be brass and have a "one sided" design), though they will work perfectly. Thanks, Flipp.


How do you fit these to the brake lines?

Posted by john on 20/05/2015

Reply from TartyBikes on 26/05/2015

Hi John - thanks for your question. These are fitted by using a shroud nut. slide the shroud nut onto the hose, and then the olive. Push the hose and olive as far as they will go into the lever body or slave cylinder, and then screw in the shroud nut. Hope that helps. Thanks, Flipp.

thomas hall

Hi are these 4mm in size?

Posted by thomas hall on 03/02/2011

Reply from TartyBikes on 07/02/2011

Hi Thomas - If you mean the internal diameter, that's 5mm. Thanks, Mark


Write a review


Based on 1 customer rating


does its job

Posted by ashley on 05/09/2012

Cheap and always handy to keep some about.

Reply from TartyBikes on 05/09/2012

Hi Ash - Magura spares do tend to be pretty good quality, and they're certainly useful if you need to shorten your hose! Thanks for the review.

People who bought this also bought…

Clean Carbon Riser

Product code: 13297



Check Stock

Check Stock

Racing Line Slave Cylinder (Single)

Product code: 12545



Hydro' Rim Brake Spares

3 colours available


3 colours available

Check Stock

Check Stock

Stan Titanium Screw On

Product code: 12074


1 offer available

Spend £40 on Stan products, get 10% off


RRP: £35.00

Save 14%


RRP: £35.00

Save 14%

Check Stock Check Stock

View options

Check Stock

Check Stock

  • © TartyBikes Ltd, 2017
  • Tel. (UK). 01772 32 33 33
  • Tel. (Intl). 0044 1772 32 33 33

TartyBikes Ltd, Units 3-4, Club Street, Bamber Bridge, Preston, PR5 6FN

  • Company No. 6131482
  • VAT. GB 860 0270 59

All prices listed are inclusive of sales tax at the correct rate for your country

Web Design & Development by Cox Web Design, Loughborough