• Opening Hours.
    Fri: 9.30am to 5.00pm (UK)
  • United Kingdom.
    01772 32 33 33
  • International.
    0044 1772 32 33 33

Clean X1 ISIS

Product code: 13864

$82.18

In stock

Clean X1 ISIS

160mm
170mm

Sold out

  • Tough yet lightweight ISIS cranks.
- Light weight but tough cranks from Clean.
- Forged then CNC machined construction offers a great balance of price, weight, strength, stiffness and quality.
- As fitted to Clean's X1 complete bikes.
- ISIS fitting is compatible with a wide range of BBs.
- 1.37" x 24tpi thread suitable for use with any threaded sprocket or freewheel we sell (unless otherwise mentioned).
- Wide threaded section allows the use of a bashring on both 160mm and 170mm options.
- Large recessed sections forged into the rear face of the crank reduce weight substantially without compromising strength.
- Tough anodised black finish is complimented by stylish laser etched graphics.
- Available in 160mm or 170mm lengths.
- Weight: 441g (170mm)
- Offset: 35mm

Additional Information

Ensure that your pedals are tightened to at least 310 in-lbs (35 Nm) every 5 minutes for the first few rides. Before fitting, it's also a good idea to make sure your pedal axles are clean (a wire brush works well) then greased before installation.
Similarly, always check crank bolt torque is at least 310 in-lbs (35 Nm) every 5 minutes for the first few rides, then each and every ride after that.
Failure to keep your pedals or crank bolts tight as described above is likely damage your cranks and this will not be covered under warranty.

Please note that the minimum required thread contact between crank arm and sprocket/freewheel is 7mm, and a 1.37" sprocket/freewheel with maximum internal thread diameter 33.80mm (NOT 1.375") must be used. Failure to adhere to this instruction will damage the cranks threads and this is not covered under warranty.

Please note: due to the manufacturing processes used for these cranks, there may be small variations in concentricity between the freewheel and bottom bracket interfaces. This can lead to a certain amount of run out for any freewheel, sprocket or adaptor installed on the crank arm. While this isn't an issue on trials bikes, for applications requiring much higher tolerances we cannot guarantee they will be suitable. Please get in touch if you have any questions.

Questions

There are currently no questions relating to this product.

Reviews

Write a review

Not yet rated

People who bought this also bought…

Clean Pro Forged

Product code: 13707

From £51.29 to £57.00

From £51.29 to £57.00

RRP: £57.00

Save up to 10%

  • Innovative pinned bar clamp!
  • Integrated headset preload top cap.
  • Available in a range of sizes.

From £51.29 to £57.00

RRP: £57.00

Save up to 10%

Check Stock Check Stock

View options

Check Stock

Check Stock

Clean Tapered Headset V2

Product code: 13394

£39.00

£39.00

£39.00

In stock In stock

Add to basket

In stock

In stock

Jitsie Race Rotor

Product code: 12524

£61.00

£61.00

£61.00

In stock In stock

View options

In stock

In stock

  • © TartyBikes Ltd, 2024
  • Tel. (UK). 01772 32 33 33
  • Tel. (Intl). 0044 1772 32 33 33

TartyBikes Ltd, Units 3-4, Club Street, Bamber Bridge, Preston, PR5 6FN

  • Company No. 6131482
  • VAT. GB 860 0270 59

Web Design & Development by tame

Top

Cookies

This site uses cookies in order to provide our customers with the best possible shopping experience. You can choose to accept all cookies or customise your cookie preferences below. For further information please read our cookie policy