• Opening Hours.
    Wed: 9.30am to 5.00pm (UK)
  • United Kingdom.
    01772 32 33 33
  • International.
    0044 1772 32 33 33

Trialtech Rim Brake Hose (1 metre)

Product code: 12791

£2.92

In stock

Trialtech Rim Brake Hose (1 metre)

Black
Blue
Clear
Green
Red
White
Yellow

Sold out

- Colourful hydraulic rim brake hose from Trialtech (not for use with disc brakes due to the higher pressures they work at).
- A perfect way to pimp up your bike!
- Suitable for use with any hydraulic rim brake system (Magura, Racing Line, Echo, Clean etc.).
- Not compatible with hydraulic disc brakes.
- Available in Black, Red and Blue with silver logos, or White, Clear, Yellow, and Green with black logos.
- Please note that the "Clear" option is clear enough to see coloured brake fluid inside, though it is not fully transparent.
- 5mm external diameter.
- Price is for one metre of hose. If you purchase a multiple quantity of one colour it will be supplied as a single length. If we don't have a single length in stock we will contact you before sending your order to check if it's ok in more than one piece.

Questions

Luke

Hi, have been looking at this pipe to make my brake look better. I was just wondering what I would need to install it onto my 05 hs33 maggie? Many thanks, Luke.

Posted by Luke on 15/01/2015

Reply from TartyBikes on 15/01/2015

Hi Luke - thanks for your question. You'd just need a pair of olives to fit this hose. You can re-use the shroud nuts that are currently on the brake, but the olives get crushed to form a seal and cannot be re-used. Hope that helps. Thanks, Flipp.

Scott

Is it possible to get these hoses in more than a 1 meter length? I want to run a longer hose on the back of my 24" street bike. Thanks guys.

Posted by Scott on 28/01/2016

Reply from TartyBikes on 28/01/2016

Hi Scott - That's no problem. If you order 2 quantities of the hose then we'd just send you one 2 metre long piece of hose. That should then be plenty for the rear of your bike (including leaving some excess for making a cross over if required). Thanks, Mark

Jamie Coupland

I can't get the barb on the end, help please???

Posted by Jamie Coupland on 16/05/2018

Reply from TartyBikes on 17/05/2018

Hi Jamie - Ideally, you'll need to use something similar to the Magura Hose Clamping Blocks (Product code: 10026). You can make your own version of them if you've got access to materials or tools. You can also make life easier by using something like a cut-down piece of spoke with a nipple on the end to help line it up. Wind a nipple onto a spoke then drop the barbed fitting onto the spoke - doing this will help it line up with the hose properly. Heating the hose up isn't required and won't work well in case you're looking to go down this route. Thanks, Mark

Ryan

Do I need just 2 olives or 2 packs of 2 olives so 4?

Posted by Ryan on 14/06/2018

Reply from TartyBikes on 15/06/2018

Hi Ryan - That will depend on the fittings on your brake, but to fit a main hose it'd be a maximum of 2 olives, so 1 pack. Thanks, Mark

Al

Bought the hose some time ago, disappointed that it not actually suitable for the arch over pipe on a hs33, guessing it is not made of nylon as it canít take barbed fittings?

Posted by Al on 06/09/2018

Reply from TartyBikes on 07/09/2018

Hi Al!
This rim brake hose is fine to use for cross-overs, and is compatible with barbed fittings or a shroud nut/olive. The Trialtech Crossover we sell is made from this same hose, and is available with barbed fittings, as shown in the product images for it.
If you haven't got some, either buying or making some Hose Clamping Blocks will help with installing the barbed fitting. We also use a cut-down piece of spoke to help line things up too - if you have the threaded end of a spoke with a little bit of extra spoke remaining, you can screw a nipple onto it and use it to help line up the fitting with the hose. You can then tap on the end of the nipple with a mallet and that helps guide the barbed fitting into the hose.
Hopefully this makes sense - if you need any more help, feel free to ask.

Roger

Does this fit hope brakes?

Posted by Roger on 23/09/2017

Reply from TartyBikes on 26/09/2017

Hi Roger - This hosing only fits hydraulic rim brakes, sorry. The only Hope compatible hose we stock is the Hope hose itself. Thanks, Mark

Reviews

Write a review

100%

Based on 2 customer ratings

Tom

Really good

Posted by Tom on 03/03/2016

Really good hose. It cuts really easily and is quite strong.

Reply from TartyBikes on 03/03/2016

Hi Tom - I'm glad you like your new hose, it does seem to work pretty well!

People who bought this also bought…

Gusset Double Six Sprocket

Product code: 2006

From £14.00 to £15.00

100%

From £14.00 to £15.00

From £14.00 to £15.00

In stock In stock

View options

In stock

In stock

Echo Slave Cylinder

Product code: 12630

£18.00

£18.00

£18.00

In stock In stock

Add to basket

In stock

In stock

Trialtech Sport Lower Tensioner Half

Product code: 12662

£20.00

£20.00

£20.00

In stock In stock

Add to basket

In stock

In stock

  • © TartyBikes Ltd, 2018
  • Tel. (UK). 01772 32 33 33
  • Tel. (Intl). 0044 1772 32 33 33

TartyBikes Ltd, Units 3-4, Club Street, Bamber Bridge, Preston, PR5 6FN

  • Company No. 6131482
  • VAT. GB 860 0270 59

All prices listed are inclusive of sales tax at the correct rate for your country

Web Design & Development by Cox Web Design, Loughborough

Top