• Opening Hours.
    Closed All Day (UK)
  • United Kingdom.
    01772 32 33 33
  • International.
    0044 1772 32 33 33

Trialtech Race Square Taper Crankset

Product code: 10079

£33.33

On order

Trialtech Race Square Taper Crankset

162mm (24T)
170mm (22T) (No Trialtech logos)

Sold out

- Great value Square Taper crankset from Trialtech!
- 24t chainring makes these a perfect replacement for many complete bikes (Onza Tyke, Rip, Bird etc.).
- Also available with a 22t chainring which is suitable for Inspired Flow 24" and 26" bikes.
- Tough forged 6061 aluminium alloy cranks complete with an aluminium bashring and steel 4-arm chainring offer superb performance at an affordable price.
- Four bolt spider with 64mm BCD (inner ring).
- Includes crank arms, bashring and chainring, already assembled and ready to fit.
- Available in a tough anodised black finish with laser etched Trialtech logos.
- 162mm or 170mm length.
- Weight: 702g (162mm length)
- Offset: 31mm

Additional Information

Ensure that your pedals are tightened to at least 310 in-lbs (35 Nm) every 5 minutes for the first few rides. Before fitting, it's also a good idea to make sure your pedal axles are clean (a wire brush works well) then greased before installation.
Similarly, always check crank bolt torque is at least 310 in-lbs (35 Nm) every 5 minutes for the first few rides, then each and every ride after that.
Failure to keep your pedals or crank bolts tight as described above is likely damage your cranks and this will not be covered under warranty.

Questions

Glenn

What spindle length is this meant to go with?

Posted by Glenn on 07/12/2010

Reply from TartyBikes on 08/12/2010

Hello - Ideally, a 128mm spindle would be best to ensure maximum clearance, although depending on your setup you may be able to use a shorter one. Thanks, Mark

stephen taylor

would a 110mm spindle length be ok?

Posted by stephen taylor on 15/12/2010

Reply from TartyBikes on 15/12/2010

Hi Stephen - That largely depends on your frame. If it's a trials frame, then almost certainly not. The shortest you could realistically use would be around 119mm. Thanks, Mark

James

hi, would these fit my onza rip 2010? whats the normal delivery time this close to christmas??? cheers James

Posted by James on 21/12/2010

Reply from TartyBikes on 21/12/2010

Hi James - They should fit your Rip fine. We're still able to dispatch orders the same day they're received (as long as they're before our cut-off time), but because of the adverse weather conditions and large volume of Christmas mail in general, delivery times from Royal Mail and our couriers are a little slow. Our couriers are advising that pre-Christmas delivery cannot be guaranteed in some parts of the UK because of this. Thanks, Mark

sean alexander

Hey there I was just wondering if these would fit the Onza Bird?

Posted by sean alexander on 11/05/2011

Reply from TartyBikes on 12/05/2011

Hi Sean - These should work fine. Thanks, Mark

Ian Hobbs

do these take a 3/32 or 1/8th inch chains. will they fit a shimano square taper chainset

Posted by Ian Hobbs on 15/06/2011

Reply from TartyBikes on 15/06/2011

Hi Ian - You can use either 3/32" or 1/8" chains with the Onza T-Bird Crankset. They should also fit on to any square taper BB. Thanks, Mark

Billy

Would this fit my onza rip 2009 if I had a shamino bottom bracket?

Posted by Billy on 06/05/2012

Reply from TartyBikes on 08/05/2012

Hi Billy - These should fit your Rip fine. Thanks, Mark

dave hadlow

will this fit on a monty x-hydra? thinking of doing bb at sametime. Would the trialtech be sufficient

Posted by dave hadlow on 10/02/2013

Reply from TartyBikes on 11/02/2013

Hi Dave - This crankset should fit on the X-Hydra fine, especially if you're using the Trialtech Race Square Taper BB with it. Thanks, Mark

cammy

Hello, would this crank fit my Onza Hitman 26"?

Posted by cammy on 07/09/2013

Reply from TartyBikes on 09/09/2013

Hi Cammy - these would fit on that bike just fine. Thanks, Flipp.

Ross Ekins

Hiya, Dont suppose this crankset will fit a Koxx Djinn 2002 model? http://i665.photobucket.com/albums/vv14/charlies106/13122009224.jpg

Posted by Ross Ekins on 24/09/2013

Reply from TartyBikes on 25/09/2013

Hi Ross - unfortunately we're not too familiar with that particular model, but there's an easy way you can find out for yourself. If you remove the crank-bolts, and look where it was seated you will find either a square hole in the crank, or a splined circle. If your cranks are the square type, and we're reasonably confident they will be, these cranks will fit your bike. If they are the other type, you will need ISIS cranks. Hope that helps! Thanks, Flipp.

callum

when do you think you will have these back in stock? is there a cheap alternative for an onza bird crankset?

Posted by callum on 05/01/2014

Reply from TartyBikes on 06/01/2014

Hi Callum - thanks for your question. Unfortunately we are unsure when we will have any of these back in stock. Our suppliers are out of stock and have no expected due date for any more. As for cheaper options, we are not aware of any. For cranks that will stand up to trials usage, 40 for a pair of cranks, chainring and bashring is about the best value for money you can get! Thanks, Flipp.

CLIVE DUDLEY

I'M IN FORT LAUDERDALE, FLORIDA. WOULD LIKE TO FIT THIS SET TO A POLARIS WOOLY BULLY FAT BIKE WITH SQUARE TAPER SHAFT ~ EXISTING CRANKS HAVE ' DOG LEG ' OUTWARDS TO CLEAR FRAME ~ ABOUT 1" FROM OUTSIDE FACE OF CHAINRING TO INSIDE OF CRANK AT THE PEDAL END. IS THIS CALLED " OFFSET " ? ANY DIMENSIONS I NEED TO CHECK BEFORE ORDERING ? MANY THANKS.

Posted by CLIVE DUDLEY on 28/02/2015

Reply from TartyBikes on 02/03/2015

Hi Clive - thanks for your question. Yes, that sounds like the Offset you're talking about, though the best way to measure it is to place the inside face of the BB/chainring end of the crank on a table, and measure the distance between the table and the inside face of the pedal end of the crank. If your cranks are the same or less than these cranks, they should fit just fine. Hope that helps. Thanks, Flipp.

Alex

Hi, I have an 2014 inspired flow which has the 170 mm 22t crank arms but they have the trial tech logo. Is there any reason why the ones you sell don't? thanks

Posted by Alex on 24/03/2016

Reply from TartyBikes on 24/03/2016

Hi Alex - The latest batch we've received from Trialtech don't appear to have the logos on. I'm not too sure why they don't have logos on there, but they're the same model of crank as the version with logos. Thanks, Mark

ricky

hi, I got a old black ashton/ edd tongue frame. think it fit on that?

Posted by ricky on 18/11/2016

Reply from TartyBikes on 21/11/2016

Hi Ricky - These cranks should fit fine depending on your BB length. If you've got a 127mm or longer BB axle then you'll be set. If it's any shorter then you might start encountering clearance issues with the chainring, although with the ET frame being designed for use with this size chainring it shouldn't be much of a problem, hopefully. Thanks, Mark

Frederick Stuart Brisbane

Would these fit a inspired fourplay?

Posted by Frederick Stuart Brisbane on 30/03/2017

Reply from TartyBikes on 31/03/2017

Hi Frederick - As long as you got a square taper BB to go along with them, these cranks should fit a Fourplay fine. Thanks, Mark

Andrew

Hi, Could you confirm if your Trailtech Square Taper Crankset is JIS or ISO size? http://www.tartybikes.co.uk/cranksets/trialtech_race_square_taper_crankset/c11p10079.html I'm after a JIS fitment. Thanks Andy

Posted by Andrew on 13/04/2017

Reply from TartyBikes on 13/04/2017

Hi Andrew - These cranks are JIS fitment. Thanks, Mark

Lee comelio

Will this fit a onza zoot looking to go up a bit on the gearing

Posted by Lee comelio on 04/08/2017

Reply from TartyBikes on 07/08/2017

Hi Lee - As long as you bought a square taper BB to go with it, this should fit the Zoot frame. However, you would need to buy a new freewheel too as you'd need to put a freewheel on the rear hub. The Zoot, as standard, is fitted with a freewheel on the crank arm whereas the Trialtech crankset has a fixed chainring. The only thing to note is that the difference in gear ratio would be relatively small, so if you're looking to dramatically change how the gear ratio feels you might not get quite what you're looking for with this unfortunately. Thanks, Mark

Ben Patrick

Hi i am looking to replace the cranks on my 24" inspired element 2012, will this crank fit it

Posted by Ben Patrick on 27/10/2017

Reply from TartyBikes on 27/10/2017

Hi Ben - If you've got Truvativ cranks fitted to your Element, then only more of the same Truvativ Hussefelt or Holzfeller cranks would fit. To fit these cranks, you'd also need to buy a square taper BB to fit them too. Thanks, Mark

Nick

Will this need a 3/32 chain or a 1/8 chain

Posted by Nick on 20/05/2018

Reply from TartyBikes on 21/05/2018

Hi Nick - You can use either chain width on this crankset. Thanks, Mark

brad morris

Does it come with the crank bolts? Many thanks, Brad

Posted by brad morris on 29/01/2011

Reply from TartyBikes on 31/01/2011

Hi Brad - The T-Bird Crankset is supplied without crank bolts. Thanks, Mark

Jordan Thornton

Hey i have a old K9 Handsome Dog 20" would this crank set fit it

Posted by Jordan Thornton on 10/07/2011

Reply from TartyBikes on 11/07/2011

Hi Jordan - As long as you have a square taper BB they should fit fine. Thanks, Mark

luke harrison

Hello, could you possibly tell me the size of the square's thats on the ends of the arm's as iam not sure the arms will fit on the axel. Thank's

Posted by luke harrison on 10/03/2012

Reply from TartyBikes on 12/03/2012

Hi Luke - The square taper on these cranks are the same as all the other models of square taper cranks available, so if you have a square taper BB then these should fit! Thanks, Mark

Lukas Schmid

Hi. Why are there only cranks for rectangular bottom brackets, but all the bottom brackets have ten teeth? Can you show me a crank, wich would fit for the Inspired Fourplay Pro 2012?

Posted by Lukas Schmid on 04/05/2016

Reply from TartyBikes on 05/05/2016

Hi Lukas - If you're hoping to re-use your bottom bracket in your Fourplay Pro, we don't stock any cranks that will fit, sorry. If you're happy to replace your bottom bracket with a new one then most of the cranks in our ISIS Cranks section will fit, along with a BB from our ISIS BBs section. Thanks, Mark

Reviews

Write a review

Not yet rated

People who bought this also bought…

Inspired Arcade Fork Adaptors

Product code: 12292

£6.00

£6.00

£6.00

In stock In stock

Add to basket

In stock

In stock

Inspired Flow 4-Bolt Bashring

Product code: 13150

£19.00

£19.00

£19.00

In stock In stock

Add to basket

In stock

In stock

Gusset File Grips

Product code: 80

£7.00

100%

Rubber Grips

6 colours available

£7.00

6 colours available

  • Great quality, comfy grips that keep your hands where they should be!

£7.00

In stock In stock

View options

In stock

In stock

  • © TartyBikes Ltd, 2018
  • Tel. (UK). 01772 32 33 33
  • Tel. (Intl). 0044 1772 32 33 33

TartyBikes Ltd, Units 3-4, Club Street, Bamber Bridge, Preston, PR5 6FN

  • Company No. 6131482
  • VAT. GB 860 0270 59

All prices listed are inclusive of sales tax at the correct rate for your country

Web Design & Development by Cox Web Design, Loughborough

Top