• Opening Hours.
    Tue: 9.30am to 5.00pm (UK)
  • United Kingdom.
    01772 32 33 33
  • International.
    0044 1772 32 33 33

Hope Crankset

Product code: 13016

From $233.62 to $391.18

Check Stock

Hope Crankset

Crank arms only (175mm, Black)
Crank Arms with Double Spider (175mm, Black)
Crank arms with Inspired Integrated Bashring & Hope BB - DISCONTINUED

Sold out

New super tough crankset from Hope Technology!

Hope Crankset
- Developed over several years with extensive FEA and rider testing, the Hope Crankset!
- A 30mm diameter axle combined with 30-spline crank/BB interface ensures the utmost strength, stiffness and durability.
- Axle length suitable for use with 68/73mm bottom brackets only.
- Splined crank arm/BB interface is improved by the use of a tapered expansion plug, ensuring a great fit time after time.
- Bearing preload adjuster ring on the non-drive crank arm allows you to dial in the tightness of the bottom bracket independently.
- Forged 7000-series alloy crank arms are incredibly stiff and strong, with CNC-machined recesses to save excess weight.
- Supplied as arms only or with a choice of bashring or removable spider:
Removable spider: this allows the use of either 2 chainrings, or a single smaller chainring with a 4-bolt bashring (such as the Inspired 4-Bolt Bashring). Inner chainring BCD: 64mm. Outer chainring/bashring BCD: 104mm.
Inspired Integrated Bashring: lightweight, compact integrated bashring and 22t chainring that fits directly onto the splines on the drive-side crank arm, compatible with both 1/8" and 3/32" chains.
- Proprietary Hope installation and extraction tools are supplied with the crankset, along with complete instructions. Please note: Failure to adhere to the recommended torque settings in the instruction manual will void warranty. Bottom bracket installation tool is not supplied with the crankset, and must be purchased separately.
- Comes with cool Hope Crankset keyring.
- Supplied with 4 chainring bolts for an inner ring and an additional 4 chainrings bolts for an outer ring or bashring.
- Anodised black finish looks great with laser teched Hope graphics.
- 175mm crank arm length.
- 141mm spacing from rear of left crank to rear of right crank gives equivalent clearance to some 22mm offset cranks on a 128mm ISIS BB. Please note: This crankset will not clear on Inspired Console or Arcade frames.
- Weight - Complete arm and axle assembly: 575.3g Spider: 58.8g

Hope External Bottom Bracket
- Tough, sealed bearing bottom built to Hope's exacting standards.
- Fitted with silky smooth double sealed Swiss-made stainless steel cartridge bearings.
- Precision machined alloy cups keep weight down.
- Supplied with 3 spacers to allow use in either 68mm, 73mm or 83mm bottom bracket shells.
- Weight: 102.2g

Additional Information

Ensure that your pedals are tightened to at least 310 in-lbs (35 Nm) every 5 minutes for the first few rides. Before fitting, it's also a good idea to make sure your pedal axles are clean (a wire brush works well) then greased before installation.
Similarly, always check the black, M6 pinch bolt torque is at least 88 in-lbs (10 Nm) every 5 minutes for the first few rides, then each and every ride after that.
Failure to keep your pedals or crank bolts tight as described above is likely damage your cranks and this will not be covered under warranty.
The red, aluminium pre-load bolt featured on these cranks should not be used to tighten them on. This is used only to pull the cranks together and pre-load the bearings. It requires only "nipping" into place, and damage caused by over-tightening is not coverable by warranty.

Questions

Ray Houston

I have an Inspired Hex Team with the Truvativ Descendant crankset. I messed up one of the crank arms and I'm looking for a replacement. Would these crank arms work on my bike?

Posted by Ray Houston

Reply from TartyBikes

Hi Ray!
Theoretically the Hope cranks will fit, but this particular model has been discontinued and replaced with the Evo crankset. We believe that the dimensions will be broadly similar so we assume they should clear too, but with no hands-on experience with them it's hard to say for sure, sorry!
Just in case - we offer a pedal thread helicoiling service, so if you've stripped the pedal threads in your Descendants we would be able to repair that for you. If it's anything major to do with the splines themselves, or the main crank arm, then it will probably be terminal unfortunately.

Reviews

Write a review

Not yet rated

People who bought this also bought…

Shimano DX Sprocket

Product code: 11012

£5.00

£5.00

£5.00

In stock In stock

View options

In stock

In stock

Trialtech Sport Splined

Product code: 10410

From £14.00 to £18.00

Splined Sprockets

2 colours available

From £14.00 to £18.00

2 colours available

From £14.00 to £18.00

Check Stock Check Stock

View options

Check Stock

Check Stock

Inspired CNC Hanger (Black)

Product code: 11438

£13.00

£13.00

£13.00

In stock In stock

Add to basket

In stock

In stock

  • © TartyBikes Ltd, 2019
  • Tel. (UK). 01772 32 33 33
  • Tel. (Intl). 0044 1772 32 33 33

TartyBikes Ltd, Units 3-4, Club Street, Bamber Bridge, Preston, PR5 6FN

  • Company No. 6131482
  • VAT. GB 860 0270 59

All prices listed are inclusive of sales tax at the correct rate for your country

Web Design & Development by Cox Web Design, Loughborough

Top

Worldwide Delivery Available

We can deliver to United States and many other countries. Click here for further info.