• Opening Hours.
    Wed: 9.30am to 5.00pm (UK)
  • United Kingdom.
    01772 32 33 33
  • International.
    0044 1772 32 33 33

Gusset Kojak Chain Tugs (pair)

Product code: 170

£6.25

Check Stock

Gusset Kojak Chain Tugs (pair)

Pair, Black
Pair, Silver

Sold out

- 10mm chain tugs to fit some bikes with horizontal dropouts.
- If your frame's dropouts are quite small (as found on most modern frames) then these will be too big. Please inquire if unsure!
- Sturdy CNC machined steel construction, with tough M8 threads (standard tugs are M6 thread).
- Now come finished in a sleek black colour, not the silver shown in the product photo.
- Sold as a pair.
- Weight: 88g

Please note that chain tugs are not designed to take any load, their job is to tension the chain and then your wheel bolt/nut keeps the wheel in place. Chain tugs breaking is not covered under warranty for this reason.

Questions

Hugh

How do they work?

Posted by Hugh on 01/01/2011

Reply from TartyBikes on 04/01/2011

Hi Hugh - How it works depends on which style of hub you're using. Essentially it is the same for either though - the Chain Tug sits between the dropout of your frame and the spacer for you axle bolt or axle nut. By tightening up the nut on the end of the threaded section of the Chain Tug, you can 'tug' your wheel backwards in the dropout. Once you've got to the correct chain tension, simply tighten up your wheel. Thanks, Mark

jack

Would this fit an Onza Blade 2009?

Posted by jack on 03/03/2011

Reply from TartyBikes on 04/03/2011

Hi Jack - If you've got a Blade '09 frame, then the best bet would probably be to get some Onza Integrated Tensioners. Your frame has a threaded mount in the dropout to use them, and they're a pretty good system, so I'd recommend them! Thanks, Mark

sam

will this fit the onza zoot 2012?

Posted by sam on 20/03/2012

Reply from TartyBikes on 20/03/2012

Hi Sam - These would fit the Zoot fine, and are a good option if you need a stronger replacement chain tug. Thanks, Mark

Peter Stevens

The thickness of the track ends on my frame are 7mm thick. Will these chain tugs fit? Cheers, Pete

Posted by Peter Stevens on 06/01/2014

Reply from TartyBikes on 07/01/2014

Hi Peter - thanks for your question. These can accommodate dropouts up to 10mm thick, so yes, they will fit your frame just fine. Thanks, Flipp.

John

HI do you think these will fit onto an Azonic Evolution frame, the one with the box section rear and horizontal dropouts?

Posted by John on 20/01/2014

Reply from TartyBikes on 21/01/2014

Hi John - thanks for your question. We've been trying to find out, but are finding it very difficult to find any information on that frame. From what we've been able to see, if the rear hub uses a 10mm diameter axle then these should work just fine. Hope that helps. Thanks, Flipp.

Jordan

Would these fit on a onza tyke.

Posted by Jordan on 05/10/2014

Reply from TartyBikes on 06/10/2014

Hi Jordan - thanks for your question. These would work just fine on a Tyke. Thanks, Flipp.

adam

will these fit the Onza comp 2013

Posted by adam on 29/02/2016

Reply from TartyBikes on 01/03/2016

Hi Adam - I believe these should fit, although the Comp has built in tensioners that generally work quite well. If you're missing the bolt for them we have replacements available in the 'Bolts' section of the website that do the trick. Thanks, Mark

Aaron

Will these fit an Ozonys Crown?

Posted by Aaron on 26/08/2017

Reply from TartyBikes on 29/08/2017

Hi Aaron - The Trialtech tugs would be a slightly easier fit. The Gusset tugs may fit, but depending on where your wheel sits in the dropouts you may need to trim a little bit of material from the section where your axle passes through. This is just to ensure that it will clear the welds on the frame. Thanks, Mark

jack taylor

Hey , would these cain tugs fit my onza comp 09 ? i have the Trialtech Chain Tugs at the moment and they seem to slip off and have snaped

Posted by jack taylor on 24/01/2011

Reply from TartyBikes on 25/01/2011

Hi Jack - They should fit fine. They should be a little stronger than the Trialtech tugs too, so hopefully they'll last a little better. Thanks, Mark

Cameron Marshall

Hey , would this fit the Onza Zoot 2010 frame?

Posted by Cameron Marshall on 29/11/2011

Reply from TartyBikes on 29/11/2011

Hi Cameron - They certainly will - the Kojaks are a very popular replacement chain tug for the Zoot as they tend to be a little more durable than the standard model. Thanks, Mark

oliver lord

Would these fit on onza ska ??

Posted by oliver lord on 12/05/2012

Reply from TartyBikes on 14/05/2012

Hello - These tugs would fit a Ska perfectly. Thanks, Mark

Gordan

So If I want to convert my snail cams to these on my '10 Echo Lite I need to put the chain tugs on the outside of the frame, and some washers on the inside to replace the snail cams? Or do these just replace the snail cams completely, on the inside of the frame?

Posted by Gordan on 10/09/2013

Reply from TartyBikes on 11/09/2013

Hi Gordan - chain tugs will not work with that frame unfortunately - only snail cams will work. Because the dropouts are so small, the circular part of the tug is too large and will prevent the bar from ever pressing on the back of the dropout to pull the wheel into line. Hope that helps. Thanks, Flipp.

Marcell Schmalhorst

will this chain tugs fit on my onza bird 2012? thanks, marcell

Posted by Marcell Schmalhorst on 28/04/2013

Reply from TartyBikes on 29/04/2013

Hi Marcell - These tugs should fit your Bird absolutely fine, and should work as a stronger upgrade to the standard ones. Thanks, Mark

Brendan Walsh

Would these fit on an old 20" Monty X-Alp frame?

Posted by Brendan Walsh on 14/01/2015

Reply from TartyBikes on 15/01/2015

Hi Brendan - thanks for your question. These might fit if the wheel sits towards the front of the dropouts, but the unthreaded section limits adjustment on shorter dropouts. Tugs with a fully threaded shaft - such as the Trialtechs - would offer better adjustment. Hope that helps. Thanks, Flipp.

Simon Smith

ive got a onza ska 2012 and the ones i had on the bike have snapped would these b fine to put on and are they the same as whats already on the bike

Posted by Simon Smith on 27/12/2013

Reply from TartyBikes on 30/12/2013

Hi Simon - thanks for your question. They are not exactly the same, but they do the same job in the same way, so they will act as a direct replacement, yes. Hope that helps. Thanks, Flipp.

Reviews

Write a review

100%

Based on 4 customer ratings

James

An unbreakable product if ever there was one!

Posted by James on 18/12/2010

Bought these after snapping the original ones that came on my Onza after only one week. Ordered online and were on my doorstep within 4 days despite the snow! Very sturdy and strong. Doubt I will break these in a hurry. Already held up to a week of non-stop riding so the forecast looks good on these little gems.

Chad

Finally Tensioners That Hold Up!

Posted by Chad on 01/08/2011

These chain tugs are the first that have been able to hold up to my riding on my Onza Pro. I have been through 3 pairs of the Trialtech type tugs (one pair was the actual Trialtech ones off of Tartybikes, the other two were Onza and a no name one). They have all bent at the bolt that attaches the axle washer to the plate if that makes any sense. Now im running these puppies machined down to 3mm wide on the inside of my frame on an Echo hub where the snail cams would normally be and let me tell you, they havent budged! Im sure they would work just as well used on the outside of the frame but this was not an option with my hub. Dont hesitate buying these, its worth saving yourself all the hassle of dealing with those other types of chain tugs from my experience.

Reply from TartyBikes on 02/08/2011

Hi Chad - Glad to hear they're working out for you. Thanks for the review!

Rourke

chain tugs

Posted by Rourke on 19/07/2013

I love these tugs, they are beefy and get the job done. I finally had the tension I wanted on my onza zoot.

Reply from TartyBikes on 22/07/2013

Hi Rourke - glad to hear you got it all working out well! Thanks for the review!

People who bought this also bought…

V!Z Rim Tape 19/20"

Product code: 10178

£2.39

100%

Rim Tapes

2 colours available

£2.39

RRP: £3.00

Save 20%

2 colours available

  • Available in Green & Red!
  • Add some colour to your bike!

£2.39

RRP: £3.00

Save 20%

Check Stock Check Stock

View options

Check Stock

Check Stock

  • Super high quality and durability!
  • Dedicated Trials caliper.
  • Tech 3 lever offers plenty of adjustability.

£160.00

In stock In stock

View options

In stock

In stock

IceToolz Pro Shop Chain Tool

Product code: 11759

£22.00

80%

£22.00

£22.00

In stock In stock

Add to basket

In stock

In stock

  • © TartyBikes Ltd, 2018
  • Tel. (UK). 01772 32 33 33
  • Tel. (Intl). 0044 1772 32 33 33

TartyBikes Ltd, Units 3-4, Club Street, Bamber Bridge, Preston, PR5 6FN

  • Company No. 6131482
  • VAT. GB 860 0270 59

All prices listed are inclusive of sales tax at the correct rate for your country

Web Design & Development by Cox Web Design, Loughborough

Top