• Opening Hours.
    Thu: 9.30am to 5.00pm (UK)
  • United Kingdom.
    01772 32 33 33
  • International.
    0044 1772 32 33 33

Neon Vertical Mount Bashplate with Bolts & Rubber

Product code: 11586

$17.08RRP: $28.48(Save 40%)

Check Stock

Neon Vertical Mount Bashplate with Bolts & Rubber

Black
Gold
Red
Silver

Sold out

- Constructed from high-grade 6061 T6 aluminium alloy.
- Features a drilled holes to save weight.
- Spacing fits Echo Lite, Echo Team 07 and 09, ZOO! Python 09, Adamant A3, Koxx Monsterboy, Ozonys XR20 and Koxx XTP frames, with vertically orientated rear bolts to prevent damage.
- Comes with Steel Bolts and Rubber Block included.
- Directional 'teeth' to increase grip when landing on obstacles, and allow the bike to slide forwards more easily.
- Weight: 102g (plus supplied bolts and rubber block at a total of 20g).

Additional Information

As with all bashplates, this product is designed to fend off knocks and protect your chain rather than be used to mount obstacles. Heavy use will cause it to break and this is not covered under warranty.

Questions

There are currently no questions relating to this product.

Reviews

Write a review

60%

Based on 3 customer ratings

kevan

Doesn't fit Rockman Austin (V2)

Posted by kevan

This doesn't fit the Rockman Austin frame, I thought this bashplate would be fine after looking at the questions and it says " this will fit your Austin fine", Got it to fit but had to modify where the top bolt went, Good points: Looks great in silver and it is also high enough to cover the freewheel. Rating: 4.5 would of been a 5 if it would fit. Thanks

Reply from TartyBikes

Hi Kevan - sorry about that, there's been a bit of a misunderstanding. These bashplates do fit the Rockman Austin. I'm assuming you're talking about the framekit you recently purchased from us - you have the Austin V2 in which case you're right and it won't fit. The mounting points are in a different place to the original Austin V1. It sounds like you've got it sorted already, but thanks for pointing it out. I'll make it a bit clearer for other people! Thanks, Flipp.

Will

Bad Fit

Posted by Will

I agree, its tight on the echo team 2009 as well and two of the supplied bolts were the wrong size, and like mentioned it doesnt cover the FW at all.

Reply from TartyBikes

Hi Will - The tight fit is largely caused by the way that the front bolts are tightening down in a different direction to the rears, so until the plate is in the right position it can be a fiddly job unfortunately. It's also strange to hear that you've had issues with freewheel coverage too - is there any chance you could send a photo of your setup to us? We've fitted these to a variety of Echo frames before and they've covered the freewheel fine before, so it'd be good to see in which way your setup differs. Regarding the bolts - sorry to hear that. If you'd be able to send them back to us we can get a replacement set sent out for you. Thanks for the review.

David

Tight Fit

Posted by David

I found that this doesn't fit the Echo Lite (2009) really all that well; I had to sand the rubber block down a bit, and then it was still a very tight fit - there is no protection to the FW (18 tooth) if I accidentally must go to bash. It is very cheap and very pretty; great clearance, but I'd really only recommend this bash-plate for 16th sprocket or freewheel.

Reply from TartyBikes

Hi David - When installing the bashplate, did you make sure to fit the spacers between the bashplate and frame? Leaving them out would be the only reason I can think of for the bashplate rubber needing to be sanded down, or for it to not cover your freewheel properly. We've installed these before and although they are a tight fit, they usually go on well and cover a freewheel correctly. Thanks for the review!

People who bought this also bought…

TartyBikes Star Nut

Product code: 10541

£3.00

100%

£3.00

£3.00

In stock In stock

View options

In stock

In stock

Inspired Vinyl Sticker

Product code: 11890

From £1.50 to £8.50

100%

Stickers

2 colours available

From £1.50 to £8.50

2 colours available

From £1.50 to £8.50

Check Stock Check Stock

View options

Check Stock

Check Stock

TartyBikes Headset Spacer

Product code: 374

From £0.50 to £2.00

Headset Spares

2 colours available

From £0.50 to £2.00

RRP: £1.00 to £2.00

Save up to 50%

2 colours available

From £0.50 to £2.00

RRP: £1.00 to £2.00

Save up to 50%

Check Stock Check Stock

View options

Check Stock

Check Stock

  • © TartyBikes Ltd, 2019
  • Tel. (UK). 01772 32 33 33
  • Tel. (Intl). 0044 1772 32 33 33

TartyBikes Ltd, Units 3-4, Club Street, Bamber Bridge, Preston, PR5 6FN

  • Company No. 6131482
  • VAT. GB 860 0270 59

All prices listed are inclusive of sales tax at the correct rate for your country

Web Design & Development by Cox Web Design, Loughborough

Top

Worldwide Delivery Available

We can deliver to United States and many other countries. Click here for further info.